Do you have an RC73 remote control and want to program it to work with your Direct TV receiver? If so, then keep reading! The RC73 can be programmed using code search or the Remote Buddy method, but to program your Direct TV remote using code search, you must first obtain the correct code from the Direct TV website. In this article, we will show you how to program your Direct TV remote RC73. We hope that this information helps you!
To program your DIRECTV remote, follow these steps: Power on your TV by pressing POWER on its remote or set-top box. While pressing and holding down 1, press and release any other number (2 through 16) in turn. These numbers are preset at the factory; you do not need to re-enter them. Now that all buttons are programmed, you can use your DIRECTV remote to control as many devices as there are buttons for. If you have additional devices that you want to be added, repeat Steps 1-4 above for each one. Your remote can hold up to 16 devices total—not all of which have to be set-top boxes. You can also add a new device if you’ve deleted one from your account. Just call DIRECTV customer service, give them your model number and they’ll add it back into your account. You should also check out our step-by-step guide to using an RC73 remote. It covers how to program a universal remote, along with more tips on programming a new device.
Steps To Program Program Your Direct TV Remote RC73
- Step 1: Connect the wires
Connect one end of a coaxial cable to your receiver, then connect the other end of your coaxial cable to an input on your TV. Take note of which port you plugged in; you’ll need it later. Connect one end of a second coaxial cable into an output on your receiver. Connect another end of that cable into an input on your VCR. If you don’t have a VCR, skip ahead to Step 3. If you do have a VCR and want to record content from your receiver onto tape, skip ahead to Step 2.
- Step 2: Put in batteries
The remote will come with 2 AA batteries. You can either use them or replace them with new ones. If you’re using new ones, please be sure they are brand-new batteries that were purchased just for use in your remote control. Not all batteries are made equally and some of them may not work well with your remote control, causing some buttons not to function correctly when you press on them. If you have used batteries already, it is recommended that you remove them from your remote and then insert fresh ones instead. This way, there won’t be any confusion as to whether or not a button is working properly because of a dead battery. Once you have inserted fresh batteries into your remote control unit, turn it on by pressing its power button located on its top side near its bottom edge.
- Step 3: Press a few buttons
Now you’re ready to program your remote. You’ll need two devices that use infrared signals: your DIRECTV system and a source device, such as a cable box or DVD player. To get started, turn on both devices and make sure they are within 30 feet of each other. Point your remote at one of them and press each button three times in quick succession. Wait for three seconds between clicks so that you can see whether or not each click was registered. If it wasn’t, try again. If it worked correctly, move on to Step 4.
- Step 4: Enjoy your new remote control
Congratulations! You have just learned how to program your DIRECTV remote. Now you can sit back and enjoy all of your favorite programs, sports, and movies! If you are still having problems with your remote control or if it is not functioning properly, please contact DIRECTV Customer Service at 1-800-531-5000 for assistance. Have a great day!
How to connect DIRECTV remote without coding?
- First, make sure that you have access to the battery compartment on your remote control. You can find this on most models by removing the cover and looking for screws that hold it in place.
- Next, remove the batteries from your remote control by unscrewing them one at a time until they’re all out of their compartment.
- Finally, replace the batteries with fresh ones and follow steps 2 and 3 again if necessary until your new batteries also aren’t working properly.
Conclusion:
Remember, when using your remote, that there are only 3 buttons you need to know about. Pressing and holding one of these buttons will access a different set of numbers than just tapping it once. So make sure you are pressing and holding on to each button until all four digits have been inputted. Also, always verify your work before hitting OK as there is no turning back from that point! And finally, don’t rush through everything! Yes, it may seem tedious at first but make sure you are being thorough and going through each step carefully. Now you know how to program direct tv remote rc73. Good luck with setting up your new remote control!
Frequently Asked Questions
- What is the problem with my DIRECTV receiver?
Remove your receiver from the wall and plug in another appliance that works (such as a lamp). If the appliance works, you have a problem with your receiver. The outlet may need to be reset if your appliance won’t turn on.
