Xfinity is an easy piece of technology that can be frustrating when the remote battery life depreciates. Sometimes, it could be stuck to a channel and unresponsive to other commands. With each model tailored to different shapes and features, it may seem hard to replace its batteries. In this article, we will show you how to change the batteries in an Xfinity remote and provide you with steps to maintain battery strength on your remote.
Xfinity remotes come with packaged batteries and replacing these batteries depends on the model and other specifications. The remote often has two flexible parts. To find the battery panel, search for a line that runs along the side. You may need to apply some pressure to pull open the battery section if you’re changing the batteries for the first time.
- In your remote version, turn the console and look for the batteries. Once the battery section has been located, press and pull down the tab to open the battery lid.
- Detach the batteries and ensure to dispose of them as they are environmentally dangerous.
- Make sure the cell area is dry and corrosion-free. Before installing the new batteries, you may need to wipe the body if you notice dirt or rust.
- Put in the new batteries and ensure to follow the battery pattern when installing them. Positive and negative symbols are contained in the section.
- Place the batteries to match the – and + symbols. Slide the battery with the negative end first (flat end of the battery). When you connect the bottom end of the battery, a band or a lever will be pressed to make it easier for the battery to slip into the enclosure.
- Close the cell door and make sure it shut at all angles after placing the batteries in your Remote.
- Run a fast test to ensure that everything is in order. If the buttons do not glow in a dark room, you may not have changed the battery properly.
What Causes A Remote’s Battery To Discharge So Quickly?
Batteries are parts of a remote that are timely. At some point, you’ll have to change them so it doesn’t cause damage to your remote. Original batteries last long but when misused, do not last long. Below are the causes of battery drains you should avoid.
- Batteries when exposed to high temperatures, drain quickly.
- Don’t continuously press or long-press the buttons. This makes the batteries run out quickly. Hold it for the shortest amount of time, and let go.
- There should be no signal interference when operating the remote as it expels the battery life. There should be no obstacles between the remote and the TV.
- Fake batteries don’t last, they tend to leak after a short well. Ensure to purchase original ones.
- When weak batteries are overused, they cause the spring of its compartment to rust. This makes new batteries run out when changed.
Duration To Change Batteries
It is important to replace batteries when you notice a slack in your remote’s output Note that batteries vary in quality and durability. Some last for weeks depending on the usage. One average battery pack can last for about six months to a year.
Checking Battery Life
It is possible to check the battery life. This keeps you informed and saves you a lot of stress. Here are the ways to monitor your battery life:
One way is to use the remote’s “Settings” button. Press the button until the remote’s top Light changes from red to green then press 9-9-9. The LED light indicates the battery power, as shown below:
- Excellent battery power: 4 green blinks
- Healthy battery power : 3 green blinks
- Fairly low battery power: 2 red blinks
- Very low battery power: 1 red blink
- Depleted battery power: 5 red blinks
Conclusion
It is important to know how to replace an Xfinity Remote also batteries don’t last forever. 2 new AA batteries are needed for the Comcast Xfinity Remote. You can get it from the majority of stores where battery packs are sold. Note that mixing new and old batteries can result in remote damage. Delay in replacing weak batteries can make your remote malfunction.
FAQ’s
- Are the Batteries Used in All Xfinity Remotes the Same?
Yes. Xfinity remotes need two AA batteries for each model. Although, they don’t support rechargeable batteries.
- What Should I Do After Replacing The Battery In My Remote?
Hold down the A (triangle) and D (diamond) keys simultaneously for 4 seconds to cause the light to turn green. Then press 9-8-1. When it is set, the LED will flicker blue three times.
- What location On The Remote Is The Setup Button?
No Setup button is present. However, you can maintain pairing the Audio Remote with the TV or other apps.
